I. Product Overview
The Shandong ROLTEC Y5-48 is an upgraded medium-pressure boiler-specific centrifugal induced draft fan developed for 1–20 t/h coal-fired, biomass and gas-fired boilers. It is designed to extract high-temperature dusty flue gas with a temperature below 250°C and stably maintain furnace negative pressure. Compared with the old Y5-47 model, it delivers larger air volume, higher efficiency and longer wear-resistant service life. It adopts two transmission types: type C belt drive and type D coupling drive, with model sizes ranging from 4C to 12.5C. It serves as the mainstream supporting equipment for flue gas exhaust systems of small and medium-sized boilers.

II. Industry-wide Application Scenarios
1. Core Supporting Equipment for Industrial Boilers (Primary Scenario)
Compatible with various industrial steam boilers and hot water heating boilers ranging from 1 to 20 tons, covering three mainstream boiler types: coal-fired boilers, biomass pellet boilers and natural gas mixed combustion boilers. It stably extracts high-temperature flue gas from combustion and balances furnace negative pressure to achieve full fuel combustion and reduce soot emissions. It is widely applied to self-provided boilers in food processing plants, printing and dyeing mills, rubber and plastic factories, foundry workshops and building material processing plants.
2. Biomass Energy Heating Projects
Special smoke exhaust equipment for heating stations fueled by straw, wood chips and rice husks. Biomass flue gas features heavy dust and drastic temperature fluctuations. The wear-resistant alloy impeller of Model Y5-48 can withstand long-term particle erosion. When matched with front-end dust removal equipment, it perfectly meets the 24-hour continuous operation demand of biomass boilers.
3. Waste Heat Kilns and Drying Production Lines
For high-temperature waste gas extraction from workpiece heat treatment drying kilns, asphalt heating furnaces, medicinal material drying lines and small hazardous waste waste heat furnaces. It can discharge humid and oil-laden flue gas generated during drying processes to guarantee workshop ventilation and constant equipment temperature. High-temperature resistant models can be customized to adapt to long-term hot air working conditions of 180℃ to 250℃.
4. Supporting Equipment for Environmental Dust Removal and Desulfurization
Serving as the negative pressure induced draft main unit at the rear of bag dust removal and water film dust removal systems to extract filtered flue gas. It matches exhaust ventilation for small-scale flue gas desulfurization and denitrification facilities to form a complete environmental treatment system and help factories meet standard exhaust emission requirements.
5. Small Kilns for Chemical and Light Industry
For high-temperature flue gas emission from small enamel furnaces, forging heating furnaces and carbonization furnaces, transporting high-temperature soot without strong corrosivity. Featuring a compact structure, it can be installed in small boiler rooms with limited factory space.
6.Urban and Rural Central Heating Boiler Rooms
Induced draft fans specially designed for 1–10 ton hot water boilers used in residential communities, industrial parks and township heating systems. Capable of non-stop long-term operation in winter with low vibration and low noise, complying with noise reduction requirements for boiler rooms in residential areas.
III. Pre-operation Working Condition Requirements
The maximum standard temperature resistance of flue gas shall not exceed 250℃; small models from 4C to 6.3C shall operate at a long-term temperature no higher than 200℃, while medium and large models of 8C and above shall normally operate at no more than 140℃.
A dust remover with dust removal efficiency of no less than 85% must be installed at the front end of the fan air inlet to control flue gas dust content at ≤150mg/m³ and greatly extend the service life of the impeller.
Only high-temperature flue gas without strong corrosivity and spontaneous combustion risk can be transported; stainless steel anti-corrosion customized models are required for flue gas with acid and alkali corrosion.
IV. FAQ
Q1: What tonnage boilers are compatible with the Y5-48 induced draft fan? What is its maximum temperature resistance?
A1: It is suitable for 1–20 t/h industrial boilers burning coal, biomass and gas. The flue gas temperature under standard working conditions shall not exceed 250°C. Models from 4C to 6.3C shall not exceed 200°C during long-term operation, and models above 8C shall normally operate within 140°C.
Q2: Is it mandatory to install a dust collector when fitting the Y5-48 fan? What consequences will arise without one?
A2: A dust removal device with dust collection efficiency of no less than 85% must be equipped. Without dust removal, the impeller will be continuously scoured by high-concentration smoke and dust, leading to blade abrasion and perforation in a short time, rapid scrapping of the fan, and greatly increased maintenance and replacement costs.
Q3: How to adjust the air volume and air pressure of the fan when the boiler load changes?
A3: A petal-type manual air damper is supplied as standard for on-site flow adjustment via opening and closing. For models with C-belt drives, the rotational speed can be altered by replacing belt pulleys. For working conditions with long-term variable loads, a variable frequency motor can be installed for superior energy-saving performance.
Q4: Can the outlet angle of the fan be modified? How many rotation directions are available?
A4: Two rotation directions are supported: left-hand rotation and right-hand rotation. Three standard outlet angles (0°, 90°, 180°) are available, which can be customized according to the boiler room pipeline layout when placing orders.
Q5: What are the differences between the Y5-48 induced draft fan and the old-style Y5-47 model, and how to choose between them?
A5: The Y5-48 is an upgraded generation product. It delivers larger air volume and a wider high-efficiency range at the same model size, with approximately 15% lower energy consumption. Its impeller adopts upgraded wear-resistant materials for stronger stability during continuous operation. The Y5-48 is the preferred choice for newly built boilers and the renovation of old fans.



